Plus UP-1100 Especificações

Water Conditioning Control System Dealer Installation, Operation and Maintenance Manual Technetic Plus Countercurrent 1100 Dealer Dealer Dealer

10or the down arrow ( ↓ ) button to decrease the number. To skip the number without changing, press the left arrow ( ← ) button. The first number stop

11Table 1 - Level 1 Programming ParametersParameterRange of ValuesMinimum IncrementsDefaultUnits of MeasureNotesName DescriptionP1Time of day AM or PM

12Table 2 - Technetic Plus 1100 System Capacity Inputs (Kilograins)Salt Setting(pounds)RESIN VOLUME (cubic feet)0.50 0.75 1.00 1.25 1.50 2.00 2.25 2.5

13Table 3 - Level II Programming ParametersParameter Range of ValuesMinimum IncrementsDefaultUnits of MeasureNotesName DescriptionP6Refill Controller1

14Level II ParametersThe programming in Level II is critical to the operation of the Technetic Plus 1100 Control.Refill control value P6, brine draw v

15Refill ControlEach Technetic Plus control valve is supplied with a refill/backwash control based on the water conditioner system size. To verify tha

16Notes on Technetic Plus EfficienciesIn order to consistently achieve the system capacities and salt efficiencies listed in Table 2, it may be necess

17with parameter P15.Fixed ReserveWhen the fixed reserve is selected, the control multiplies the maximum system capacity by the percent value set in p

183. Relieve resin tank pressure:A. Remove control valve cover.B. Press down on the top of the drive gear to disengage the cam gear.C. With the cam ge

19Riser Pipe AssemblyThe dimensions provided here will make it easy for assemblers to cut the riser pipe when building the Technetic Plus softeners.Fi

2Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Installation. . . . . . . . . . . . . . . . . . . . . .

20SpecificationsHydrostatic Test Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21Flow Diagrams

22Pressure Loss Characteristics

231100 Valve Body

24Series 1265 Bypass ValveCodePartNo. Description Qty. CodePartNo. Description Qty.1 1034448 Valve Body Assembly 1 16 1040717 Valve Disc Kit 12 103434

25TroubleshootingThe control valve may be manually indexed to each regeneration position as follows:1. Remove the control valve cover, Figure 7.2. Pre

26Table 7 - Troubleshooting ProceduresProblem Possible Cause Solution1. Capacity display stays at 9999 even through there is water usage.a. Total syst

2710. Control does not regenerate automatically or when REGEN button is depressed.a. Transformer unplugged.b. No electric power at outlet.c. Defective

www.Technetic Plus.com15. Intermittent or irregular brine draw.a. Low water pressure.b. Defective injector.a. Increase water pressure (20 psi at condi

3IntroductionThe Technetic Plus 1100 Control valve provides sophisticated, demand-based water conditioning by incorporating a microprocessor and a wat

4Superior Design• Hybrid Distribution System keeps resin compacted and maximizes salt efficiency.• Clear aircheck provides viewing of brine draw and r

5InstallationAll plumbing must conform to local codes. Inspect the unit carefully for carrier shortage or shipping damage.Location SelectionThe follow

6Note: Standard commercial practices have been expressed here. Local codes may require changes to these suggestions.Brine Line ConnectionInstall the b

7the cover at the bottom, towards the back. Spread the sides apart slightly and lift off. Figure 7.Figure 72. Disconnect power to the control by unplu

8not recede, if it goes up, or if air enters the transparent air check chamber and the ball falls and seats, refer to the Troubleshooting section in t

9Programming the Technetic Plus 1100 ControlFigure 11This section covers all aspects of programming the control. The control is shipped from the facto